| 1 | ACPI: RSDP signature @ 0xC00FE0B0 checksum 0
|
|---|
| 2 | ACPI: RSDP 000FE0B0, 0024 (r2 HP )
|
|---|
| 3 | ACPI: XSDT 77FC81BC, 0064 (r1 HPQOEM SLIC-MPC 1 HP 1)
|
|---|
| 4 | ACPI: FACP 77FC8084, 00F4 (r4 HP 0944 3 HP 1)
|
|---|
| 5 | ACPI Error (tbfadt-0453): 32/64X address mismatch in "Pm2ControlBlock": [00008800] [0000000000008100], using 64X [20070126]
|
|---|
| 6 | ACPI: DSDT 77FC84A4, 11437 (r1 HP SB400 10000 MSFT 3000001)
|
|---|
| 7 | ACPI: FACS 77FE7D80, 0040
|
|---|
| 8 | ACPI: SLIC 77FC8220, 0176 (r1 HPQOEM SLIC-MPC 1 HP 1)
|
|---|
| 9 | ACPI: EPTH 77FC8398, 0038 (r1 HP 0944 1 HP 1)
|
|---|
| 10 | ACPI: APIC 77FC83D0, 0062 (r1 HP 0944 1 HP 1)
|
|---|
| 11 | ACPI: MCFG 77FC8434, 003C (r1 HP 0944 1 HP 1)
|
|---|
| 12 | ACPI: TCPA 77FC8470, 0032 (r2 HP 0944 1 HP 1)
|
|---|
| 13 | ACPI: SSDT 77FD98DB, 0059 (r1 HP HPQNLP 1 MSFT 3000001)
|
|---|
| 14 | ACPI: SSDT 77FD9934, 0206 (r1 HP PSSTBLID 1 HP 1)
|
|---|
| 15 | ACPI: DMI detected: Hewlett-Packard
|
|---|
| 16 | ATI board detected. Disabling timer routing over 8254.
|
|---|
| 17 | ACPI: PM-Timer IO Port: 0x8008
|
|---|
| 18 | ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
|
|---|
| 19 | Processor #0 15:8 APIC version 16
|
|---|
| 20 | ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
|
|---|
| 21 | Processor #1 15:8 APIC version 16
|
|---|
| 22 | ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
|
|---|
| 23 | ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
|
|---|
| 24 | IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
|
|---|
| 25 | ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
|
|---|
| 26 | ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
|
|---|
| 27 | Enabling APIC mode: Flat. Using 1 I/O APICs
|
|---|
| 28 | Using ACPI (MADT) for SMP configuration information
|
|---|
| 29 |
|
|---|
| 30 | ENABLING IO-APIC IRQs
|
|---|
| 31 | ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
|
|---|
| 32 | ...trying to set up timer (IRQ0) through the 8259A ... failed.
|
|---|
| 33 | ...trying to set up timer as Virtual Wire IRQ... works.
|
|---|
| 34 |
|
|---|
| 35 | ACPI: EC: non-query interrupt received, switching to interrupt mode
|
|---|
| 36 | ACPI: Interpreter enabled
|
|---|
| 37 | ACPI: (supports S0 S3 S4 S5)
|
|---|
| 38 | ACPI: Using IOAPIC for interrupt routing
|
|---|
| 39 | ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
|
|---|
| 40 | ACPI: EC: driver started in interrupt mode
|
|---|
| 41 | ACPI: PCI Root Bridge [C08B] (0000:00)
|
|---|
