Pre-defined Queries

Custom Query (11973 matches)

Filters
 
Or
 
  
 
Columns

Show under each result:


Results (1 - 3 of 11973)

1 2 3 4 5 6 7 8 9 10 11
Ticket Resolution Summary Owner Reporter
#1607 fixed 00:12.0 IDE interface: ATI Technologies Inc 4379 Serial ATA Controller (rev 80) marcusoverhagen mrsunshine
Description

Chip is bases on the Silicon Image 3112 if im not mistaking. Fails to boot, have added vendor and device ID to the silicon image driver but no luck there.

Strange thing is that the boot finds it in two places.

One that says: Vendor 0x1002 Device 0x4379 class_base 0x01 class_sub 0x01

then another one that looks like lspci output but somewhat extended.

Added a TRACE before it excludes devices inthe silicon_image_3112 driver to see what devices it looks over, and this one is not with in that list. there 0x4376, 0x437b (i think) 0x4377 ... but none of them is this device. Or can it be that it finds a generic_ide driver (for the IDE controller on the mobo) and just stops scannig there?.

lspci -vv output: 00:12.0 IDE interface: ATI Technologies Inc 4379 Serial ATA Controller (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])

Subsystem: Acer Incorporated [ALI] Unknown device 010f Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 8440 [size=8] Region 1: I/O ports at 8434 [size=4] Region 2: I/O ports at 8438 [size=8] Region 3: I/O ports at 8430 [size=4] Region 4: I/O ports at 8400 [size=16] Region 5: Memory at b0004000 (32-bit, non-prefetchable) [size=512] [virtual] Expansion ROM at 6c000000 [disabled] [size=512K] Capabilities: [60] Power Management version 2

Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME-

Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-

Address: 00000000 Data: 0000

#1773 fixed $0 is set incorrectly axeld andreasf
Description

$0 should contain the (relative) path to the executable, not the command used to call it.

The following test script:

#!/bin/sh
echo $0

called with test.sh prints ./test.sh on BeOS but test.sh on Haiku.

This seems to keep aclocal et al. from working, since $0 returns aclocal but the path to call itself is e.g. config/bin/aclocal.

#7441 not reproducible 1024x600 screen resolution doesn't work on Acer Aspire AO532h nobody sotrud_nik
Description

(This bug is similiar to http://dev.haiku-os.org/ticket/6202)

Tried latest hrev41211 It shows only blank black screen with backlight is on.

It did show the colorfull mess on screen before http://dev.haiku-os.org/changeset/41154

Syslog and listdev's outputs are attached.

1 2 3 4 5 6 7 8 9 10 11
Note: See TracQuery for help on using queries.