Ticket #17412: nvidia.settings

File nvidia.settings, 3.3 KB (added by Kitsune64, 3 years ago)

Nvidia.settings file for the NVIDIA Driver that work with the Geforce4 4200 Go from laptop Dell Latitude D800. Place this file in /boot/home/config/settings/kernel/drivers/

Line 
1# Settings file for the nvidia driver and accelerant
2#
3# This file should be moved to the directory
4# ~/config/settings/kernel/drivers/
5#
6
7# nvidia driver parameters:
8#accelerant "nvidia.accelerant" # if enabled selects accelerant filename to be used
9#primary "10de_0110_010000" # if enabled selects device to be used as primary device ('hack')
10dumprom false # dump bios rom to file (in home folder)
11
12# nvidia.accelerant parameters:
13usebios true # if true rely on bios to coldstart the card
14#memory 2 # in MB, override builtin memory size detection
15hardcursor true # if true use on-chip cursor capabilities
16#logmask 0x00000000 # nothing logged, is default
17#logmask 0x08000604 # log overlay use in full to file (in home folder)
18#logmask 0xffffffff # log everything to file (in home folder)
19switchhead false # switch head assignment (dualhead cards only)
20force_pci true # block AGP mode use if true (AGP cards only)
21dma_acc true # if true enable DMA cmd fetching for 2D acc (instead of using PIO)
22#tv_output 0 # disabled or 0 = autodetect, 1 = Y/C (and CVBS if possible), 2 = CVBS
23force_sync false # if true forces 3D rendering to be synchronized to the vertical retrace
24force_ws false # if true forces widescreen type detection for all connected screens
25block_acc false # if true disables the acceleration engine
26
27# WARNING: tweak alert! modify stuff below on your own risk...
28unhide_fw false # if true 'unhide' cards AGP fastwrite support on cards that hide it
29pgm_panel false # if false don't program DVI and laptop panel pixelclocks (refreshrates)
30vga_on_tv false # if true enables VGA output on the head outputting to TV
31#gpu_clk 150 # in Mhz, (tries to) override default GPU clockspeed (be carefull!!!)
32#ram_clk 150 # in Mhz, (tries to) override default cardRAM clockspeed (be carefull!!!)
33check_edid true # if true blocks resolutions beyond monitor(s) capabilities
34
35#--------- that's all.
36
37
38#logmask setup info:
39#log level select:
40#logmask 0x0000000x # lowest digit: bitmask to select logging level.
41
42#log modules select:
43#logmask 0xxxxxxxx0 # highest 7 digits: bitmask to select individual modules to log.
44
45#log levels: (3D add-on adheres to this setup, 2D add-on still has to tuned)
46#logmask 0x00000001 # log rendering
47#logmask 0x00000002 # log state
48#logmask 0x00000004 # log experimental
49#logmask 0x00000008 # log errors
50
51#log modules:
52#logmask 0x00000100 # engine: agp
53#logmask 0x00000200 # engine: bes
54#logmask 0x00000400 # overlay
55#logmask 0x00000800 # engine: support
56#logmask 0x00001000 # engine: dac2
57#logmask 0x00002000 # engine: info
58#logmask 0x00004000 # engine: i2c
59#logmask 0x00008000 # engine: general
60#logmask 0x00010000 # engine: dac1
61#logmask 0x00020000 # engine: crtc2
62#logmask 0x00040000 # engine: crtc1
63#logmask 0x00080000 # engine: acc (both PIO and DMA)
64#logmask 0x00100000 # engine: brooktree tv
65#logmask 0x00200000 # set displaymode
66#logmask 0x00400000 # propose displaymode
67#logmask 0x00800000 # init accelerant
68#logmask 0x01000000 # get timing constraints
69#logmask 0x02000000 # get mode info
70#logmask 0x04000000 # get device info
71#logmask 0x08000000 # get accelerant hook
72#logmask 0x10000000 # engine management
73#logmask 0x20000000 # cursor
74#logmask 0x40000000 # 2D acceleration
75#logmask 0x80000000 # 3D acceleration