Haiku will not boot on Gigabyte GA-H61N-USB3 motherboard

[andrewz]

I just got a new, used motherboard and it won't boot. It displays the boot icons and stops there. I tried to boot from CD and from a pre-built disk and there is no difference. I enabled safe boot with no difference. When I enable debug logging it does this:

... add_memory_type_range from 105 to 115 then PCI: PCI controller found PCI: FixupDevices: checking bus 1, 2, 3 PCI: Dom 0, bus 0, dev 28, func 0 changed PCI bridge control from 0x0000 to 0x0003

Does this 3 times then stops

Only USB devices are mouse and kb. 8 GB RAM, quad core CPU.

[korli]

Could you add the output of "lspci -vvv" from a Linux boot?

[andrewz]

Output from lspci -vvv pasted below:

00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09)

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) (prog-if 00 [VGA controller])

Subsystem: Giga-byte Technology Device d000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 46 Region 0: Memory at fb800000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at ff00 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-

Address: fee0f00c Data: 4122

Capabilities: [d0] Power Management version 2

Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

Capabilities: [a4] PCI Advanced Features

AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP-

Kernel driver in use: i915

00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)

Subsystem: Giga-byte Technology Device 1c3a Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 10 Region 0: Memory at fbfff000 (64-bit, non-prefetchable) [size=16] Capabilities: [50] Power Management version 3

Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+

Address: 0000000000000000 Data: 0000

00:1a.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI])

Subsystem: Giga-byte Technology Device 5006 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2

Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features

AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP-

Kernel driver in use: ehci-pci

00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)

Subsystem: Giga-byte Technology Device a002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 47 Region 0: Memory at fbff4000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2

Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+

Address: 00000000fee0f00c Data: 4152

Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00

DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us

ExtTag- RBE- FLReset+

DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes

DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us

ClockPM- Surprise- LLActRep- BwNot-

LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-

ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-

Capabilities: [100 v1] Virtual Channel

Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-

Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress-

VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-

Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=1 ArbSelect=Fixed TC/VC=02 Status: NegoPending- InProgress-

Capabilities: [130 v1] Root Complex Link

Desc: PortNumber=0f ComponentID=00 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+

Addr: 00000000fed1c000

Kernel driver in use: snd_hda_intel

00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode])

Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fbd00000-00000000fbdfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-

PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00

DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us

ExtTag- RBE+ FLReset-

DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes

DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us

ClockPM- Surprise- LLActRep+ BwNot-

LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-

Slot #0, PowerLimit 10.000W; Interlock- NoCompl+

SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-

Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-

Changed: MRL- PresDet- LinkState+

RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd- DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB

Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB

LnkSta2: Current De-emphasis Level: -3.5dB

Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-

Address: 00000000 Data: 0000

Capabilities: [90] Subsystem: Giga-byte Technology Device 5001 Capabilities: [a0] Power Management version 2

Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

Kernel driver in use: pcieport

00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode])

Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fbe00000-fbefffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-

PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00

DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us

ExtTag- RBE+ FLReset-

DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes

DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us

ClockPM- Surprise- LLActRep+ BwNot-

LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-

Slot #1, PowerLimit 10.000W; Interlock- NoCompl+

SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-

Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-

SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-

Changed: MRL- PresDet- LinkState+

RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd- DevCtl2: Completion Timeout: 260ms to 900ms, TimeoutDis- ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB

Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB

LnkSta2: Current De-emphasis Level: -6dB

Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-

Address: 00000000 Data: 0000

Capabilities: [90] Subsystem: Giga-byte Technology Device 5001 Capabilities: [a0] Power Management version 2

Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

Kernel driver in use: pcieport

00:1d.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI])

Subsystem: Giga-byte Technology Device 5006 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at fbffd000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2

Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features

AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP-

Kernel driver in use: ehci-pci

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a5) (prog-if 01 [Subtractive decode])

Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-

PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

Capabilities: [50] Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard

00:1f.0 ISA bridge: Intel Corporation H61 Express Chipset Family LPC Controller (rev 05)

Subsystem: Giga-byte Technology Device 5001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel driver in use: lpc_ich

00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])

Subsystem: Giga-byte Technology Device b005 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 40 Region 0: I/O ports at fe00 [size=8] Region 1: I/O ports at fd00 [size=4] Region 2: I/O ports at fc00 [size=8] Region 3: I/O ports at fb00 [size=4] Region 4: I/O ports at fa00 [size=32] Region 5: Memory at fbffc000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-

Address: fee0f00c Data: 4191

Capabilities: [70] Power Management version 3

Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004 Capabilities: [b0] PCI Advanced Features

AFCap: TP+ FLR+ AFCtrl: FLR- AFStatus: TP-

Kernel driver in use: ahci

00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)

Subsystem: Giga-byte Technology Device 5001 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at fbffb000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 0500 [size=32] Kernel driver in use: i801_smbus

01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)

Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 48 Region 0: I/O ports at ee00 [size=256] Region 2: Memory at fbdff000 (64-bit, prefetchable) [size=4K] Region 4: Memory at fbdf8000 (64-bit, prefetchable) [size=16K] Capabilities: [40] Power Management version 3

Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-

Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+

Address: 00000000fee0f00c Data: 4162

Capabilities: [70] Express (v2) Endpoint, MSI 01

DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us

ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-

DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 4096 bytes

DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 <64us

ClockPM+ Surprise- LLActRep- BwNot-

LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB

Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB

LnkSta2: Current De-emphasis Level: -6dB

Capabilities: [b0] MSI-X: Enable- Count=4 Masked-

Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800

Capabilities: [d0] Vital Product Data

No end tag found

Capabilities: [100 v1] Advanced Error Reporting

UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-

Capabilities: [140 v1] Virtual Channel

Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-

Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress-

Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00 Kernel driver in use: hrev8169

02:00.0 USB Controller: Fresco Logic Device 1009 (rev 02) (prog-if 30 [XHCI])

Subsystem: Giga-byte Technology Device 5007 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fbee0000 (64-bit, non-prefetchable) [size=64K] Region 2: Memory at fbeff000 (64-bit, non-prefetchable) [size=4K] Region 4: Memory at fbefe000 (64-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 3

Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

Capabilities: [50] MSI: Enable- Count=1/8 Maskable- 64bit+

Address: 0000000000000000 Data: 0000

Capabilities: [70] Express (v2) Endpoint, MSI 00

DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited

ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-

DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-

RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes

DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited

ClockPM- Surprise- LLActRep- BwNot-

LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+

ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-

LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB

Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB

LnkSta2: Current De-emphasis Level: -6dB

Capabilities: [b0] MSI-X: Enable+ Count=8 Masked-

Vector table: BAR=2 offset=00000000 PBA: BAR=4 offset=00000000

Capabilities: [100 v1] Advanced Error Reporting

UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-

Kernel driver in use: xhci_hcd

[pulkomandy]

​http://www.haiku-os.org/community/forum/new_nightly_wont_boot_gigabyte_gah61nusb3_motherboard mentions that disabling xHCI in the BIOS makes it boot.

[phoudoin]

Sounds like FL1009 xHCI controller is not exactly behaving as the Intel implementation does. Or our xHCI driver is too much focusing on Intel implementation. Or both :(

[korli]

I'd like to remind that the xhci bus driver is not yet enabled, so only the lack of xhci support can be an issue.