wifi seems not to work with a BCM4312 : Vendor: 0x14e4, device:0x4312

[filscauj]

Hello,

I just finished to install HAIKU on may laptop (hp dv9000). Then I read the "welcome" text with WebPositive and follow the procedure for BCM43xx :

with my wired link in a terminal session I just enter the :

-> install-wifi-firmware.sh.

then the script downloads some firmware (I can' show you this because i made it before the issue), and at the end, the script seems finish without errors.

what I can see is the driver bcm43xx seems to see a 0x4311 device in place of 0x4312 ...In fact I don't know i the script is running well or not because at the first boot this is already the case (0x4311) ...

So how can I check the script is perfectly running ?

I just show you a shot cut of my syslog file concernig BCM43xx:

first the PCI scanning is detecing well the card :

KERN: PCI: [dom 0, bus 3] bus 3, device 0, function 0: vendor 14e4, device 4312, revision 02 KERN: PCI: class_base 02, class_function 80, class_api 00 KERN: PCI: vendor 14e4: Broadcom Corporation KERN: PCI: device 4312: BCM4312 802.11a/b/g (Broadcom 802.11a/b/g WLAN) KERN: PCI: info: Network controller KERN: PCI: line_size 10, latency 00, header_type 00, BIST 00 KERN: PCI: ROM base host 00000000, pci 00000000, size 00000000 KERN: PCI: cardbus_CIS 00000000, subsystem_id 1371, subsystem_vendor_id 103c KERN: PCI: interrupt_line 0b, interrupt_pin 01, min_grant 00, max_latency 00 KERN: PCI: base reg 0: host b0200000, pci b0200000, size 00004000, flags 04 KERN: PCI: base reg 1: host 00000000, pci 00000000, size 00000010, flags 0f KERN: PCI: base reg 2: host 00000000, pci 00000000, size 00000000, flags 00 KERN: PCI: base reg 3: host 00000000, pci 00000000, size 00000000, flags 00 KERN: PCI: base reg 4: host 00000000, pci 00000000, size 00000000, flags 00 KERN: PCI: base reg 5: host 00000000, pci 00000000, size 00000000, flags 00 KERN: PCI: Capabilities: PM, vendspec, MSI, PCIe

the the driver is loaded but it seems to have some issue with the MAC rev 13 :

KERN: broadcom43xx: init_driver(0x81ec6228) KERN: [broadcom43xx] (bwi) bus_alloc_resource(3, [16], 0x0, 0xffffffff, 0x1,0x2) KERN: add_memory_type_range(1788, 0xb0200000, 0x20000, 0) KERN: set MTRRs to: KERN: mtrr: 0: base: 0x7ff60000, size: 0x20000, type: 0 KERN: mtrr: 1: base: 0xb0000000, size: 0x2000000, type: 0 KERN: mtrr: 2: base: 0xc0000000, size: 0x40000000, type: 0 KERN: mtrr: 3: base: 0x80000000, size: 0x80000000, type: 1 KERN: [broadcom43xx] (bwi) bus_alloc_resource(1, [0], 0x0, 0xffffffff, 0x1,0x6) KERN: [broadcom43xx] (bwi) BBP: id 0x4311, rev 0x2, pkg 0 KERN: [broadcom43xx] (bwi) MAC rev 13 is not supported KERN: [broadcom43xx] (bwi) no MAC was found KERN: remove_memory_type_range(1788, 0xb0200000, 0x20000, 0)

Thanks a lot for your replies